| ID |
Date |
Author |
Type |
Category |
Subject |
|
39
|
Tue Mar 21 09:59:52 2006 |
Alec | 8-ID-I | Setups | Do Young Noh coherent diffraction |
Some misc. notes from Do Young Noh's (DYN) experiment time - March 14--21, 2006
- DYN JJ slits should work with bipolar and microstepper drives but found only fully reliable behavior with bipolar drives (SPD-6B's)
- Use microns as slit units as don't have enough resolution in spec otherwise with mm units
- Did not save all motor settings for the DYN JJ slits, but recall the following:
(1/2 step mode)
48 steps/rev,
gap/aperture = 39.024 microns/revolution
center = 15.485 microns/revolution
- ti4 table had to be lowered by approx. 5 mm
- Used Newport crossed x-z stage (that we use for Lois Pollack) to support addition beam mask at end of flight path
|
|
40
|
Tue Mar 21 10:00:56 2006 |
Alec | 8-ID General | Beamline Hardware | Axis 241Q video server |
Password for the root and sandy accounts is the usual I user account password
| Quote: |
- An Axis 241Q video server has been placed on our network. Currently, its IP address is 164.54.116.175 and its host name cymophane (though I have not figured out how to access it via its host name).
- There is a link to the video server from the 'Local' section of our web page. Alternatively, use this link: http://164.54.116.175/view/index.shtml
- The manual for installation and the user guide are attached below.
- Some salient points are as follows:
(1) Basically you just access the web site listed above to connect to the video server
(2) A connection via IE provides additional functionality provided you connect with adminsitrator rights (the first time anyway) so that you can install the MPEG-4 decoder
(3) The MPEG-4 stream uses less bandwidth than the Motion JPEG but does require the decoder
(4) From a Windows PC and MPEG-4, you can save images and zoom the display to full screen
- root and sandy are adminstrator login names. The password is available locally
|
|
|
41
|
Fri Mar 24 17:05:06 2006 |
Alec | 8-ID-D | Problem | monochromator encoders-gonio2 |
| Moncohromator encoder on gonio2 does not update with moves |
|
42
|
Fri Mar 24 17:07:02 2006 |
Alec | 8-ID-D | Problem | diamchi table record |
| displays yellow text "Comm. Failure" and, perhaps related, Michael is seeing diamchi bounce back to its original position after moves. Temporarily fixed by turning off gonio1 and gonio2 motors |
|
43
|
Tue Mar 28 17:14:13 2006 |
Alec | 8-ID-D | Problem | monochromator encoders-gonio2 |
| Quote: | | Moncohromator encoder on gonio2 does not update with moves |
Problem was that gonio2 drive channel has was changed - from 8 -> 5 but the accompanying encoder cable plugged into the back of the StepPak was not moved. Once the encoder cable was moved, the encoder updated as expected. |
|
44
|
Tue Mar 28 17:26:39 2006 |
Alec | 8-ID-D | Controls | moving diamchi, gonio1, gonio2, 8idd:sm1, 8idd:Table1 |
User access security has been enabled for these motors per http://8id.xor.aps.anl.gov/elog/8-ID/42.
To use these motors, you must start medm from the workstation glass.xor.aps.anl.gov and be logged in or su -l as s8idadm. |
|
48
|
Tue Apr 25 22:16:48 2006 |
Alec | 8-ID General | Shutdown Activities | 2006-2 (May 2006) shutdown task list - ver 0.11 |
| Revised shutdown task list from 8-Id Ops meeting on 4/25/2006 |
| Attachment 1: Projects_v0-11.xls
|
| Attachment 2: Projects_v0-11.pdf
|
|
49
|
Wed Apr 26 13:17:54 2006 |
Alec | 8-ID General | Presentations | 2006/04/26 TRR Group Meeting presentation |
| Update presented to TRR group meeting on 4/26/06. Shutdown plans and I monochromator install update. |
| Attachment 1: TRR_Group_Meeting_Update_2006-04-24.ppt
|
| Attachment 2: OldAndNewBeam.ppt
|
|
50
|
Wed Apr 26 15:21:20 2006 |
Alec | 8-ID General | Presentations | New ANL brand (2006) poster template |
| I have attached a poster template from Rich Fenner reflecting the new ANL brand (as of Feb. 2006 or so). I am guessing it will change soon because it does not look that polished, but in the meantime, this is what to use. |
| Attachment 1: APS_POSTER_TMPLT.ppt
|
|
51
|
Thu May 18 14:17:18 2006 |
Alec | 8-ID General | Controls | PV archiver add list - 2006-05-18 |
|
| Attachment 1: ADD_8IDPVlist_20060517.txt
|
8ida:D1Ch31_calc / ID:8:a:D1Ch31_calc
8ida:D1Ch31_raw / ID:8:a:D1Ch31_raw
8ida:D1Ch32_calc / ID:8:a:D1Ch32_calc
8ida:D1Ch32_raw / ID:8:a:D1Ch32_raw
8idi:D1Ch1_calc / ID:8:i:D1Ch1_calc
8idi:D1Ch1_raw / ID:8:i:D1Ch1_raw
8idi:D1Ch2_calc / ID:8:i:D1Ch2_calc
8idi:D1Ch2_raw / ID:8:i:D1Ch2_raw
8idi:D1Ch3_calc / ID:8:i:D1Ch3_calc
8idi:D1Ch3_raw / ID:8:i:D1Ch3_raw
8idi:D1Ch4_calc / ID:8:i:D1Ch4_calc
8idi:D1Ch4_raw / ID:8:i:D1Ch4_raw
8idi:D1Ch5_calc / ID:8:i:D1Ch5_calc
8idi:D1Ch5_raw / ID:8:i:D1Ch5_raw
8idi:D1Ch13_calc / ID:8:i:D1Ch13_calc
8idi:D1Ch13_raw / ID:8:i:D1Ch13_raw
8idi:D1Ch18_calc / ID:8:i:D1Ch18_calc
8idi:D1Ch18_raw / ID:8:i:D1Ch18_raw
8idi:D1Ch21_calc / ID:8:i:D1Ch21_calc
8idi:D1Ch21_raw / ID:8:i:D1Ch21_raw
8idi:D1Ch22_calc / ID:8:i:D1Ch22_calc
8idi:D1Ch22_raw / ID:8:i:D1Ch22_raw
8idi:D1Ch24_calc / ID:8:i:D1Ch24_calc
8idi:D1Ch24_raw / ID:8:i:D1Ch24_raw
8idi:D1Ch25_calc / ID:8:i:D1Ch25_calc
8idi:D1Ch25_raw / ID:8:i:D1Ch25_raw
8idi:D1Ch27_calc / ID:8:i:D1Ch27_calc
8idi:D1Ch27_raw / ID:8:i:D1Ch27_raw
8idi:D1Ch28_calc / ID:8:i:D1Ch28_calc
8idi:D1Ch28_raw / ID:8:i:D1Ch28_raw
8idi:D1Ch29_calc / ID:8:i:D1Ch29_calc
8idi:D1Ch29_raw / ID:8:i:D1Ch29_raw
8idi:D1Ch30_calc / ID:8:i:D1Ch30_calc
8idi:D1Ch30_raw / ID:8:i:D1Ch30_raw
8idi:D1Ch31_calc / ID:8:i:D1Ch31_calc
8idi:D1Ch31_raw / ID:8:i:D1Ch31_raw
8idi:D1Ch32_calc / ID:8:i:D1Ch32_calc
8idi:D1Ch32_raw / ID:8:i:D1Ch32_raw
8idi:D1Ch33_calc / ID:8:i:D1Ch33_calc
8idi:D1Ch33_raw / ID:8:i:D1Ch33_raw
8idi:D1Ch34_calc / ID:8:i:D1Ch34_calc
8idi:D1Ch34_raw / ID:8:i:D1Ch34_raw
8idi:D1Ch35_calc / ID:8:i:D1Ch35_calc
8idi:D1Ch35_raw / ID:8:i:D1Ch35_raw
8idi:D1Ch36_calc / ID:8:i:D1Ch36_calc
8idi:D1Ch36_raw / ID:8:i:D1Ch36_raw
8idi:D1Ch37_calc / ID:8:i:D1Ch37_calc
8idi:D1Ch37_raw / ID:8:i:D1Ch37_raw
8idi:D1Ch38_calc / ID:8:i:D1Ch38_calc
8idi:D1Ch38_raw / ID:8:i:D1Ch38_raw
8idi:D1Ch40_calc / ID:8:i:D1Ch40_calc
8idi:D1Ch40_raw / ID:8:i:D1Ch40_raw
8idi:m49 / ID:8:i:m49
8idi:m49.DVAL / ID:8:i:m49.DVAL
8idi:m50 / ID:8:i:m50
8idi:m50.DVAL / ID:8:i:m50.DVAL
8idi:m51 / ID:8:i:m51
8idi:m51.DVAL / ID:8:i:m51.DVAL
8idi:m52 / ID:8:i:m52
8idi:m52.DVAL / ID:8:i:m52.DVAL
8idi:m53 / ID:8:i:m53
8idi:m53.DVAL / ID:8:i:m53.DVAL
8idi:m54 / ID:8:i:m54
8idi:m54.DVAL / ID:8:i:m54.DVAL
8idi:m55 / ID:8:i:m55
8idi:m55.DVAL / ID:8:i:m55.DVAL
8idi:m56 / ID:8:i:m56
8idi:m56.DVAL / ID:8:i:m56.DVAL
8idi:table3.AX / ID:8:i:table3.AX
8idi:table3.AY / ID:8:i:table3.AY
8idi:table3.AZ / ID:8:i:table3.AZ
8idi:table3.X / ID:8:i:table3.X
8idi:table3.Y / ID:8:i:table3.Y
8idi:table3.Z / ID:8:i:table3.Z
|
|
52
|
Thu May 18 14:17:56 2006 |
Alec | 8-ID General | Controls | 8-ID PV Archiver Delete List - 2006/05/18 |
|
| Attachment 1: DELETE_8IDPVlist_20060517.txt
|
8ida:AD4enc1:count / ID:8:a:AD4enc1:count
08:ID:A:Tvac:CC1:Pres / ID:8:A:Tvac:CC1:Pres
08:ID:A:Tvac:CC2:Pres / ID:8:A:Tvac:CC2:Pres
08:ID:A:Tvac:CV1:Pres / ID:8:A:Tvac:CV1:Pres
08:ID:A:Tvac:CV2:Pres / ID:8:A:Tvac:CV2:Pres
8ida:D1Ch13_calc / ID:8:a:D1Ch13_calc
8ida:D1Ch13_raw / ID:8:a:D1Ch13_raw
8ida:D1Ch18_calc / ID:8:a:D1Ch18_calc
8ida:D1Ch18_raw / ID:8:a:D1Ch18_raw
8ida:D1Ch19_calc / ID:8:a:D1Ch19_calc
8ida:D1Ch19_raw / ID:8:a:D1Ch19_raw
8idd:m3 / ID:8:d:m3
8idd:m3.DVAL / ID:8:d:m3.DVAL
8idd:m4 / ID:8:d:m4
8idd:m4.DVAL / ID:8:d:m4.DVAL
8idd:m5 / ID:8:d:m5
8idd:m5.DVAL / ID:8:d:m5.DVAL
8idd:m6 / ID:8:d:m6
8idd:m6.DVAL / ID:8:d:m6.DVAL
8idd:m7 / ID:8:d:m7
8idd:m7.DVAL / ID:8:d:m7.DVAL
8idd:m8 / ID:8:d:m8
8idd:m8.DVAL / ID:8:d:m8.DVAL
8idd:m9 / ID:8:d:m9
8idd:m9.DVAL / ID:8:d:m9.DVAL
8idd:m9EncCalc / ID:8:d:m9EncCalc
8idd:sm2 / ID:8:d:sm2
8idd:sm2.DVAL / ID:8:d:sm2.DVAL
8idd:sm3 / ID:8:d:sm3
8idd:sm3.DVAL / ID:8:d:sm3.DVAL
8idd:sm4 / ID:8:d:sm4
8idd:sm4.DVAL / ID:8:d:sm4.DVAL
8idd:sm5 / ID:8:d:sm5
8idd:sm5.DVAL / ID:8:d:sm5.DVAL
8idd:sm6 / ID:8:d:sm6
8idd:sm6.DVAL / ID:8:d:sm6.DVAL
8idd:sm7 / ID:8:d:sm7
8idd:sm7.DVAL / ID:8:d:sm7.DVAL
8idd:sm8 / ID:8:d:sm8
8idd:sm8.DVAL / ID:8:d:sm8.DVAL
8idd:sm9 / ID:8:d:sm9
8idd:sm9.DVAL / ID:8:d:sm9.DVAL
8idd:sm10 / ID:8:d:sm10
8idd:sm10.DVAL / ID:8:d:sm10.DVAL
8idi:hsc1:b / ID:8:i:hsc1:b
8idi:hsc1:height / ID:8:i:hsc1:height
8idi:hsc1:t / ID:8:i:hsc1:t
8idi:hsc1:v0 / ID:8:i:hsc1:v0
8idi:hsc2:b / ID:8:i:hsc2:b
8idi:hsc2:height / ID:8:i:hsc2:height
8idi:hsc2:h0 / ID:8:i:hsc2:h0
8idi:hsc2:l / ID:8:i:hsc2:l
8idi:hsc2:r / ID:8:i:hsc2:r
8idi:hsc2:t / ID:8:i:hsc2:t
8idi:hsc2:v0 / ID:8:i:hsc2:v0
8idi:hsc2:width / ID:8:i:hsc2:width
|
|
53
|
Fri May 19 10:44:36 2006 |
Alec | 8-ID-I | Setups | I Mono mapped positions and table potentiometers after coarse reposition |
| Mapped I optical table after rough x-ray beam alignment was completed at end of 2006-1. Mapped positions shown in word doc. Then did coarse reposition of the optical table and returned via motorized stages to mapped positions. Optical table potentiometers after this return to mapped position was complete are shown in the powerpoint slide. |
| Attachment 1: SurveyMapping_20060519.doc
|
| Attachment 2: ti1_table_potentiometer_20060519.ppt
|
|
54
|
Tue May 23 16:59:55 2006 |
Alec | 8-ID General | EPS | EPS Programmer - John Servino - contact information |
Code in the 8-ID EPS system is currently supported by John Servino - a consultant - from Professional Automation Services. Contact info for him is as follows:
APS extension - 2-3573 (not listed in the directory_
Cell - 847-519-1000
Pager - 708-242-6627 |
|
55
|
Wed May 24 17:35:24 2006 |
Alec | 8-ID- | EPS | Temporary control of the 8-ID-G valve - Valve 11 |
The EPS HMI interface is not currently connected to the Valve 11 (8-ID-G) vacuum valve open and close signals. A temporary fix is to open and close this valve via EPICS (the EPS will still close this valve if necessary, it is only the HMI interface that is not working). To open and close Valve 11, do the following
1) From the HMI, Valve Control screen, Enable EPICS Valve Control
2) Use 'probe' and "Adjust"
to set the PV 8ida:V2001_4 to On (Open) and 8ida:V2001_5 to Off (Closed) ---- To open the valve
and the opposite for closing the valve |
|
64
|
Thu Jun 8 11:34:56 2006 |
Alec | 8-ID-I | Setups | I monochromator mono beam height change with angle/energy |
As the monochromatic energy selected by the new I mono is changed, the beam moves vertically by a small but not insignificant amount.
The vertical offset versus monochromator Bragg angle is given by:
deltaZ = Crystal Gap * 2 * cos(theta_Bragg) = 3.1 * 2 * cos(theta_Bragg) using the current best estimate of the gap = 3.1 mm
So to calculate the vertical change between 2 energies, just take the difference between calculations at the 2 different Bragg angles. Incidentally, the I mono Bragg angle can be retrieved from the soft motor monoth = 8idi:sm32 |
|
71
|
Wed Jul 5 16:58:10 2006 |
Alec | 8-ID-I | Experiment | Near Field Speckle |
ti4 table potentiometer and motor readings before moving coolsnap camera
ti4zu - 7.2081 VDC -> 9.0786 mm
ti4zdi - 4.5267 VDC -> 14.8594 mm
ti4zdo - 4.2067 VDC -> 16.2452
And EPICS User / Dial positions
ti4xu = 14.00098 mm / 14.001115 mm
ti4xd = 16.00095 mm / 16.00095 mm
ti4zu = 6.11455 mm / 6.114415 mm
ti4zdi = 14.72946 mm / 14.72946 mm
ti4zdo = 16.659225 mm / 16.659225 mm
ti4_x = 14.621634 mm
ti4_z = 10.899796 mm
moved mono on Friday
ti1_x = 5.87 |
|
73
|
Wed Jul 12 15:57:07 2006 |
Alec | 8-ID General | Computers and Network | XOR server network path names |
From http://ww2.xor.aps.anl.gov/computing/info/Computer_Info/200505/20050513.0.html
and in general the xor info server site
http://ww2.xor.aps.anl.gov/computing/info/Computer_Info/Computer_Info.html
Solaris Path Linux Path
------------- -----------------------------
/home/1-bm /net/beams-nfs/export/1-bm
/home/1-id /net/beams-nfs/export/1-id
/home/2-bm /net/beams-nfs/export/2-bm
/home/2-idb /net/beams-nfs/export/2-idb
/home/2-idb1 /net/beams-nfs/export/2-idb1
/home/2-idd /net/beams-nfs/export/2-idd
/home/2-ide /net/beams-nfs/export/2-ide
/home/aussie /net/beams-nfs/export/aussie
/home/beams /net/beams-nfs/export/beams
/home/beams1 /net/beams-nfs/export/beams1
/home/ftp1 /net/beams-nfs/export/ftp1
/home/joule /net/beams-nfs/export/joule
/home/local /net/beams-nfs/export/local
/home/sector3 /net/beams-nfs/export/sector3
/home/2bm-tomo /net/users-nfs/export/2bm-tomo
/home/8-id /net/users-nfs/export/8-id
/home/8-ide-a /net/users-nfs/export/8-ide-a
/home/8-ide-b /net/users-nfs/export/8-ide-b
/home/8-ide-c /net/users-nfs/export/8-ide-c
/home/8-ide-d /net/users-nfs/export/8-ide-d
/home/8-idi-a /net/users-nfs/export/8-idi-a
/home/8-idi-b /net/users-nfs/export/8-idi-b
/home/8-idi-c /net/users-nfs/export/8-idi-c
/home/8-idi-d /net/users-nfs/export/8-idi-d
/home/ftp2 /net/users-nfs/export/ftp2
/home/scratch /net/users-nfs/export/scratch
/home/sector30 /net/users-nfs/export/sector30
/home/sector4 /net/users-nfs/export/sector4
/home/users /net/users-nfs/export/users
/home/users1 /net/users-nfs/export/users1 |
|
76
|
Wed Jul 19 09:52:57 2006 |
Alec | 8-ID General | Controls | EPICS boot scripts |
EPICS boot script location to see what serial port is assigned to what, for example ...
/home/xorApps/epics/synApps_4_5/ioc/8id/iocBoot
then go to the crate and then look at st.cmd |
|
77
|
Thu Jul 20 11:46:42 2006 |
Alec | 8-ID General | Software | convert.i script for uncompressing SMD data |
From yorick, first read in convert_imm3.i and then can use following file to uncompress compressed SMD data:
parent = "/home/8-idi-a/simon_0606/"
//change the foll. 3 lines and change the format command for >9999
//images
child="lu_w_13_34.35C_01"
first_frame=1
last_frame=4000
//change the above 3 lines
first_frame=swrite(format="%04d",first_frame)
last_frame=swrite(format="%04d",last_frame)
print,oldname,newname
oldname = parent+child+"/"+child+"_"+first_frame+"-"+last_frame+".imm"
newname = parent+child+"/"+child+"_ucp_"+first_frame+"-"+last_frame+".imm"
convert_imm(oldname,newname) |
|
92
|
Tue Aug 15 10:07:01 2006 |
Alec | 8-ID General | Detectors | chip damage on the new dalsa/smd after surface xpcs |
One week of surface xpcs produced the following (but detector just puit back in beamlne so temperature is still elevated):
 |